Custom – Production – Design – Factory
WhatsApp: +86 17330216660

Impact Idler Set Basics for Conveyor Loading Points

What an Impact Idler Set Does

An impact idler set is the shock-absorbing group of rollers installed on a conveyor belt right where material is loaded or transferred. Instead of a standard steel trough roller, this set carries rubber rings or a rubber-covered roller surface so falling rock, clinker, or ore hits something that gives a little. That cushioning protects the belt carcass and the roller itself, and it keeps the belt tracking more steadily through the loading zone.

The set is still an idler assembly, not a pulley. Drive pulleys, tail pulleys, and bend pulleys do different jobs at the ends of the conveyor and are not replacements for it. An impact roller set is usually compared with a normal trough idler set or a transition idler set, because the difference is mainly in the roller surface and the shock load it can take.

Impact Idler Set

How the Set Is Built

A typical impact idler set is a three-roll trough group, often at 30 or 35 degrees, with a frame that mounts on the conveyor bracket. The rollers may be steel tubes fitted with rubber rings, or tubes with a thicker rubber sleeve. The rubber rings are spaced along the roller so the belt is supported between them while impact energy is spread out rather than concentrated at one point.

Impact Idler Set

Bearing selection follows the shaft and load design, not a fixed rule from belt width. Common bearing numbers on conveyor idler rollers include 6204, 6205, 6305, 6306, 6308, and 6310, and the same roller diameter can appear with more than one bearing choice depending on the duty. Seals matter as much as the bearing in a dusty loading area, so look for a multi-labyrinth or similar contact seal arrangement.

Common Reference Sizes

The values below are typical reference points for discussion, not a fixed match between one belt width and one roller size. Roller length also changes with trough angle and with whether the roll is a side roll or a center roll.

Item Common reference range
Roller diameter Ø63, Ø76, Ø89, Ø102, Ø108, Ø127, Ø133, Ø159, Ø178, Ø194, Ø219 mm
Belt width B400, B500, B650, B800, B1000, B1200, B1400, B1600, B1800, B2000, B2200, B2400
Trough angle 20, 30, 35, 45 degrees
Roller surface steel tube, nylon, ceramic, rubber ring
Group form single roll, two-roll, three-roll trough

For example, a three-roll trough set on B800 might use rolls around 315 mm long, and on B1200 around 465 mm, but side rolls and center rolls can differ and the final length is set by the design. Do not assume a Ø127 roller only fits one belt width, or that a given belt width forces one shaft diameter.

Impact Idler Set

Where It Fits on the Line

You will see impact idler sets at the discharge chute of a primary crusher, under a transfer tower, and at the feed point of a screen. In a quarry or aggregate line they sit below the crusher outlet where stone drops with force. In a coal mining or underground coal mining conveyor, they appear at bunker discharge and at belt-to-belt transfer points. Cement plants use them under clinker and limestone chutes, and power plant coal handling systems use them where coal falls from the tripper or the feeder.

Impact Idler Set

The belt above the set is often a heavy-duty or impact resistant conveyor belt, sometimes an EP conveyor belt or a steel cord conveyor belt on the longer runs. A rubber conveyor belt with good abrasion resistance is common in the same loading zone. The set works together with the conveyor bracket and the frame, so check that the mounting height matches the adjacent trough idlers.

What to Check Before Ordering

  • Belt width and trough angle, since these set the roll length and the frame opening.
  • Drop height and lump size at the loading point, which guide the rubber ring thickness and roller diameter.
  • Roller diameter and shaft size, matched to the existing bracket rather than chosen from belt width alone.
  • Bearing and seal type for dusty or wet conditions.
  • Whether the set must align with transition idlers on either side.

Maintenance is mostly about watching the rubber rings for wear, checking that rollers still turn freely, and replacing a seized roll before it scuffs the belt. A worn impact set that no longer turns becomes a drag point and can damage the belt cover quickly.

Summary

An impact idler set is a loading-zone roller group with a cushioned surface, built to take the hit that a standard trough idler should not. Match it to the belt width, the drop, and the existing bracket, and keep it separate in your mind from the drive, tail, and bend pulleys at the ends of the conveyor.