What the EP1000 1200mm Conveyor Belt Is
The EP1000 1200mm conveyor belt is a heavy-duty fabric-core belt built around a 1200mm wide carcass rated at EP1000. In plain terms, it is an EP conveyor belt with polyester-nylon (EP) fabric plies whose nominal tensile strength reaches 1000 N/mm per ply, supplied in a 1200mm width. This combination makes it a practical choice for main haulage lines in mines, quarries, cement works, power plants and sand and gravel yards where a wide, strong belt must carry large tonnages without excessive stretch.
An accurate equivalent name for the same product is an EP1000 fabric core conveyor belt, 1200mm wide. It is an EP rubber conveyor belt, not a steel cord or NN design, and that distinction matters when matching it to a conveyor structure.
Construction and Materials
The carcass is usually made of multiple EP fabric plies, commonly 2 to 6 layers depending on the required strength and safety factor. Rubber skim between plies bonds the layers, while top and bottom cover compounds protect the carcass from abrasion, impact, moisture and, where specified, heat, oil or flame. Common cover combinations include 4+2 mm, 5+2 mm and 6+2 mm, with thicker covers used in high-abrasion duty.
Edge construction, splice method and cover grade are usually agreed at ordering. Buyers can request variants such as an abrasion resistant conveyor belt for sharp stone, a flame retardant conveyor belt for coal handling, or a heat resistant conveyor belt for clinker and sinter. These are cover and compound choices on the same EP1000 platform, not different belt families.
Where It Fits in a Conveyor
A 1200mm belt is a common wide-belt size on trunk conveyors feeding crushers, stockpiles and ship loaders. On such a line, the belt runs over idler roller sets, wraps the head drive pulley and tail pulley, and is supported by conveyor brackets and frames. Drive, tail and bend pulleys each have their own role and are not interchangeable; the belt width alone does not fix any pulley or shaft diameter. Layout, tension and pulley face width should be confirmed with the conveyor designer.
Typical duty includes bulk material conveyor belt service in iron ore, copper ore, coal, limestone, aggregates and cement raw meal. In dusty or underground coal mining conveyor belt applications, anti-static and flame retardant properties are often requested. For steep inclines, a chevron conveyor belt or corrugated sidewall belt may be compared, but those are separate designs and do not replace the EP1000 flat belt where a conventional troughing line is used.
Reference Specifications
The following values are common references, not fixed supply promises. Actual construction is confirmed per order and per design.
- Belt type: EP1000 fabric core conveyor belt (EP conveyor belt)
- Nominal strength: EP1000, 1000 N/mm per ply
- Belt width: 1200mm (B1200)
- Carcass: multi-ply EP fabric, typically 2 to 6 plies
- Cover grades available: abrasion resistant, heat resistant, flame retardant, oil resistant, cold resistant, anti-static
- Common cover thickness: 3+1.5, 4+2, 5+2, 6+2, 8+3 mm
- Splice: vulcanized or mechanical, per site practice
For comparison, narrower or wider options in the same EP series include the 1000mm and 1400mm widths, and strength grades run from EP200 up through EP1250 and beyond. A buyer selecting an EP1000 1200mm belt should check the required strength grade against the actual tension, not simply copy a neighbouring line.
Buyer Checklist
- Confirm the calculated belt tension and safety factor before fixing EP1000.
- State the material, lump size, temperature and moisture so the cover grade is right.
- Check pulley face width, trough angle and idler spacing for a 1200mm belt.
- Agree cover thickness, edge type and splice method in writing.
- For coal or dusty service, specify flame retardant and anti-static requirements.
- Plan storage and handling to avoid carcass damage before installation.
Matching the belt to the conveyor, rather than to a single number, keeps a heavy-duty mining conveyor belt running longer. A correctly specified EP1000 1200mm conveyor belt, with suitable idler roller and conveyor pulley support, is a sound base for wide, high-tonnage haulage in mining, cement, power and aggregate operations.
