Custom – Production – Design – Factory
WhatsApp: +86 17330216660

1400mm Diameter Conveyor Pulley in Heavy Bulk Handling Systems

What a 1400mm Diameter Conveyor Pulley Is

A 1400mm diameter conveyor pulley is a large-diameter drum used at key transfer points on high-capacity belt conveyors. In practice it is often called a Ø1400mm conveyor drum or a 1.4m belt conveyor pulley. It is not simply a scaled-up small pulley; the larger shell, heavier shaft and more robust bearing arrangement are chosen to handle high belt tensions and thick, wide belts. Drive, tail and bend pulleys are distinct positions in the conveyor layout, and a 1400mm diameter unit can be specified for any of them depending on the duty.

The size usually appears where belt widths are substantial, for example B1200, B1400, B1600 or wider, and where the conveyor carries abrasive or heavy bulk material. A 1400mm diameter pulley is often paired with a Steel Cord Conveyor Belt or a high-strength EP Conveyor Belt in primary crushing and long-haul circuits.

1400mm Diameter Conveyor Pulley

Construction Details That Matter

The pulley normally consists of a rolled steel shell, end discs, a shaft, bearing housings and a lagging surface. Common surface forms include plain, hot-vulcanized rubber, cold-bonded rubber, diamond grooving and ceramic lagging, with lagging thickness typically 8, 10, 12, 15 or 20 mm. For a 1400mm diameter drum, the larger circumference gives more wrap contact and helps reduce belt slip when the drive duty is high.

Shaft diameter is not derived from belt width alone. It is determined by torque, radial load, bearing span and the conveyor designer’s safety factors. Common shaft sizes in this class may range from Ø160 to Ø200 and beyond, but the final value must come from the drive calculation.

1400mm Diameter Conveyor Pulley

Typical Industrial Applications

These large pulleys are found in primary crushing stations at a quarry, in iron ore and copper ore transfer houses, and in power plant coal handling systems. A 1400mm diameter conveyor pulley is also used in cement plant clinker lines and port bulk terminals where wide belts move heavy tonnage. In these locations the pulley works together with the conveyor belt, idler roller sets and conveyor bracket assemblies to keep the belt tracking and tensioned.

Mining duty often calls for a Flame Retardant Conveyor Belt or Abrasion Resistant Conveyor Belt, while dusty coal routes may use an Anti-Static Conveyor Belt. The pulley lagging should be selected to match the material and the environmental conditions, not only the belt type.

1400mm Diameter Conveyor Pulley

Size Reference and Related Components

The table below gives common reference values only. They are not fixed combinations, and actual dimensions are confirmed by design.

Item Common reference values
Pulley diameter Ø1000, Ø1250, Ø1400, Ø1600 mm
Belt width (B) B1000, B1200, B1400, B1600, B1800 mm
Shell face width Usually wider than belt, e.g. B1200 about 1400 mm, B1400 about 1600 mm
Lagging thickness 8, 10, 12, 15, 20 mm
Shaft diameter Ø120, Ø140, Ø160, Ø180, Ø200 mm (by torque and load)

Do not assume that one belt width can only match one pulley diameter. A B1400 conveyor might use a Ø1000mm tail pulley and a Ø1400mm drive pulley in the same circuit, because the head and tail positions carry different tensions.

Buyer Checklist Before Ordering

  • Confirm the pulley position: drive, tail, bend, take-up or snub. These are not interchangeable, and each has different load and wrap requirements.
  • State the belt width, belt type and maximum belt tension so the shell and shaft can be checked.
  • Choose the lagging surface and thickness for the actual material: plain for light duty, diamond or ceramic for wet and slippery conditions.
  • Check the bearing type, housing and lubrication method against the maintenance plan.
  • Verify the shaft diameter from the conveyor design, not from a catalog guess.
  • Review the interface with the conveyor bracket and frame before fabrication.

For high-tonnage lines in mining, cement and port operations, a 1400mm diameter conveyor pulley is a long-life component when the lagging, bearings and shaft are correctly matched to the belt and the load profile. Buyers should ask for a dimension drawing and a load calculation rather than relying on a nominal size alone.