What a 1200mm Wide Conveyor Belt Is
A 1200mm wide conveyor belt is a 1200mm Conveyor Belt built for conveying lines that need a wider carrying surface than the common 800mm or 1000mm widths. In practice, the belt is usually a fabric-cored or steel-cord reinforced rubber belt with a cut width of 1200mm, supplied as an open length or as an Endless Conveyor Belt for specific pulley centers. The 1200mm figure describes the belt width only; thickness, carcass, cover grade and tensile strength are separate choices made for each conveyor.
Because of its width, this size is often grouped with the Wide Conveyor Belt family and is common on main haulage and plant transfer conveyors in mining, coal preparation, cement, power generation, quarries and sand and aggregate plants.
How the Belt Is Built
A typical 1200mm wide belt combines three elements: the carcass, the covers and the edges. The carcass carries the tension and may be Multi-Ply Fabric Core Conveyor Belt construction, an EP Conveyor Belt or NN Conveyor Belt, or a Steel Cord Conveyor Belt for long, high-tension routes. Cover rubber protects the carcass from abrasion, impact, heat, oil or flame, and edge construction affects tracking and resistance to edge damage.

Common cover thickness combinations for this width include 4+2 mm, 5+2 mm, 6+2 mm and 8+3 mm, with 2 to 6 plies in fabric constructions. These are reference values; final specifications should follow the conveyor design and the supplier’s data sheet.

Typical Specification Ranges
The table below shows commonly referenced values for a 1200mm wide belt. Treat them as orientation only, not as a fixed catalogue.
- Width: 1200mm (B1200)
- Fabric carcass: EP200, EP315, EP400, EP500, EP630, EP800, EP1000, EP1250, EP1600
- Nylon carcass: NN100, NN200, NN300, NN400
- Steel cord: ST1000, ST1250, ST1600, ST2000 and heavier grades
- Cover grades: abrasion resistant, heat resistant, oil resistant, flame retardant, anti-static, cold resistant, acid and chemical resistant
- Surface forms: plain, Chevron Conveyor Belt, Skirted Conveyor Belt, Corrugated Sidewall Conveyor Belt
- Cover thickness: 3+1.5, 4+2, 5+2, 6+2, 8+3 mm
Where It Fits in the Plant
At 1200mm, a belt can move large tonnages without excessive belt speed. It is frequently found on primary crusher discharge conveyors, stockyard and port conveyors, ship loading lines and cement plant clinker routes. In coal mining and underground coal mining, a 1200mm flame retardant belt is often paired with idler roller sets and conveyor pulley assemblies sized for the duty. The same width appears in power plant coal handling, iron ore and copper ore transport, and aggregate conveyor lines feeding screens and crushers.
Selection depends on the material: a Mining Conveyor Belt for hard rock may need a high abrasion resistant cover, while a Heat Resistant Conveyor Belt is used for clinker or sinter. A Fire Resistant Conveyor Belt or Anti-Static Conveyor Belt is specified where dust and gas hazards exist, and an Oil Resistant Conveyor Belt suits oily scrap or recycled material.

Selection Pointers for Buyers
Start with the conveyor design rather than the belt alone. Confirm the required tensile grade, the number of plies or cord class, cover thickness, and whether the belt will be spliced on site or supplied as an Endless Conveyor Belt. Check pulley diameters, troughing angle and transition distances with the conveyor pulley supplier; a 1200mm belt is not tied to one pulley size, and shaft diameters must come from the conveyor design, not from the belt width.
Also verify the idler roller spacing, load support and belt training. Wider belts are less tolerant of misalignment, so adequate conveyor bracket and frame rigidity matters. For steep inclines, a Chevron Conveyor Belt or Corrugated Sidewall Conveyor Belt may be considered, but these are different belt constructions and should not be substituted for a plain 1200mm belt without rechecking the conveyor.
Finally, request test data and splice instructions, and store the belt on a clean, dry surface before installation. For more guidance on matching a 1200mm Wide Conveyor Belt with rollers, pulleys and brackets, review the conveyor layout with your supplier before ordering.







