What a PVC Mining Conveyor Belt Is
A PVC Mining Conveyor Belt is a solid-woven or fabric-reinforced belt whose covers and carcass are based on polyvinyl chloride rather than plain rubber. In practice, the product is often called a PVC conveyor belt or a solid woven PVC belt, and it is a familiar sight in underground coal mining, cement plants, power plants, and quarry operations where flame resistance and low weight matter. Unlike a Multi-Ply Fabric Core Conveyor Belt built from rubber-covered plies, the PVC construction usually forms a single, cohesive body that resists delamination and moisture ingress.
The belt is not a universal answer to every haulage job. It earns its place where fire safety, moderate tensile demand, and stable troughing are the priorities, while a Steel Cord Conveyor Belt or a heavy EP Conveyor Belt handles longer, higher-tonnage runs.

How the Belt Is Built
Most constructions start with a woven fabric core, often polyester or nylon yarns, that is impregnated and coated with PVC compound. The cover layers are formulated for the duty: a Flame Retardant Conveyor Belt grade for underground coal faces, an Anti-Static Conveyor Belt grade where dust and methane are present, or a plain abrasion-focused compound for sand and stone. Some designs add a thin rubber cover for extra grip, which is why buyers sometimes compare a PVC belt with a Rubber Conveyor Belt on the same conveyor.

Edge construction matters as much as the cover. Properly sealed edges keep water and fines out of the carcass, and a well-finished splice keeps the belt running true over the conveyor pulley and idler roller sets. A PVG Conveyor Belt, which combines PVC impregnation with rubber covers, sits between the two families and is often specified for underground coal Mining Conveyor Belt duties where higher friction is needed.
Where It Fits in the Plant
Typical duties include:
- Underground coal mining conveyor lines and gate roads
- Coal Mining Conveyor Belt runs from shaft to preparation plant
- Cement plant clinker and raw meal transfer
- Power plant coal yard and boiler feed conveyors
- Quarry Conveyor Belt and Aggregate Conveyor Belt lines
- Sand making plant and stone crushing conveyor circuits
In a cement or power plant, the belt usually works alongside a conveyor pulley at the drive, a tail pulley at the loading end, and bend pulleys that route the return strand. These pulley roles are distinct and are not interchangeable. The same applies to conveyor brackets and idler roller types: a troughing idler and a return idler cannot be swapped, and the belt width alone does not fix the pulley diameter or shaft size — those follow the conveyor design.

Common Sizes and Grades
The table below shows reference values that appear in general catalogues. They are typical ranges, not fixed pairings, and final selection depends on the conveyor design, load, and environment.

Belt Widths
| Designation | Nominal Width |
|---|---|
| B500 | 500 mm |
| B650 | 650 mm |
| B800 | 800 mm |
| B1000 | 1000 mm |
| B1200 | 1200 mm |
| B1400 | 1400 mm |
| B1600 | 1600 mm |
| B1800 | 1800 mm |
| B2000 | 2000 mm |
Strength and Cover Reference
| Item | Common Reference |
|---|---|
| Tensile grades | EP200 to EP2000 class wording appears in fabric belts; PVC solid woven grades are quoted separately by the maker |
| Cover thickness | 3+1.5, 4+2, 5+2, 6+2, 8+3 mm |
| Carcass plies | 2 to 6 layers in fabric constructions |
Do not read the width table as a pulley matching chart. A 1200 mm belt can run on different pulley diameters depending on tension and wrap angle.
Buyer Checklist
Before ordering, confirm the flame and anti-static requirements for the site, the material size and drop height at the loading point, and whether oil, heat, or cold will attack the cover. Ask for the splice method and the recommended idler roller spacing. For very abrasive ore, a High Abrasion Resistant Conveyor Belt or a rubber-covered belt may outlast a standard PVC cover. For long overland routes, compare with an NN Conveyor Belt or EP belt before committing.
Also check that the belt matches the existing conveyor pulley lagging and the conveyor bracket geometry, and keep spare PVG800S or similar splice kits on hand where the line runs continuously. A correctly specified PVC Mining Conveyor Belt, matched to its pulleys and idlers, gives reliable service in mines, cement works, and power stations alike.







