Custom – Production – Design – Factory
WhatsApp: +86 17330216660

Five-Roll Idler Set for Tough Conveyor Duties

What a Five-Roll Idler Set Is

A five-roll idler set is a conveyor belt support assembly that uses five rollers in one frame to shape the belt into a deep trough. It is also called a five-roller troughing set. This arrangement differs from the common three-roll set by adding two extra rolls, which creates a more rounded profile and spreads the load across more contact points. The set is mounted on the carrying side of a conveyor and works together with the conveyor belt, conveyor pulley, and conveyor bracket to keep material centered and moving smoothly.

In bulk handling plants such as a quarry, cement plant, or power plant coal yard, a five-roll idler set can be a practical choice where belt width and material load demand extra support. It is not a replacement for drive, tail, or bend pulleys; those are separate components with different duties.

Five-Roll Idler Set

How the Assembly Is Built

The set usually consists of five idler rollers mounted in a steel frame. The outer rolls are angled more steeply than in a three-roll design, and the two intermediate rolls bridge the gap between the side rolls and the center roll. Roll diameters commonly range from Ø63 to Ø219 mm, with Ø89, Ø108, Ø127, and Ø159 being frequent choices for medium and heavy conveyors. Bearing sizes such as 6204, 6205, 6305, 6306, 6308, and 6310 appear across different roll diameters, but no single bearing is tied to one roll size.

Five-Roll Idler Set

Roll surfaces may be plain steel, nylon, ceramic, or rubber rings. Rubber rings are often selected for impact zones, while ceramic or nylon covers may be used where wear or material buildup is a concern. The frame connects to the conveyor bracket, and the whole set sits under the loaded belt.

Five-Roll Idler Set

Where It Fits on the Conveyor

Five-roll idler sets are typically used on the carrying side of long overland or plant conveyors. They are common in applications that handle abrasive or heavy bulk material, such as iron ore, copper ore, limestone, clinker, and coal. A five-roll troughing set can help maintain a deeper trough angle, often 35 or 45 degrees, which improves belt centering when the conveyor is fully loaded.

They are not usually found on the return side; return idlers are a different subtype, such as flat return or V-return rolls. Likewise, impact idlers and self-aligning idlers serve specific purposes, and a five-roll set is not a substitute for those designs when impact absorption or belt training is the main requirement.

Common Sizes and Configuration Notes

Roll length changes with belt width, trough angle, and frame design. The table below gives common examples for reference only; actual dimensions are determined by the conveyor design. Side rolls and center rolls may differ in length within the same set.

Five-Roll Idler Set

Belt width Typical roll length (example) Common roll diameter range
B500 about 200 mm Ø63 to Ø108 mm
B650 about 250 mm Ø76 to Ø127 mm
B800 about 315 mm Ø89 to Ø133 mm
B1000 about 380 mm Ø108 to Ø159 mm
B1200 about 465 mm Ø108 to Ø178 mm
B1400 about 530 mm Ø127 to Ø194 mm
B1600 about 600 mm Ø133 to Ø219 mm
B1800 about 670 mm Ø159 to Ø219 mm
B2000 about 750 mm Ø159 to Ø219 mm

These values are not fixed pairings. A B1000 conveyor, for example, may use different roll diameters depending on load, speed, and frame space. Buyers should confirm the shaft diameter, bearing type, and frame mounting dimensions with the conveyor designer rather than assuming a size from belt width alone.

What a Buyer Should Check

  • Confirm the trough angle and roll arrangement required for the existing conveyor frame.
  • Match the idler roller diameter and bearing to the load and speed, not just the belt width.
  • Check that the conveyor bracket bolt pattern fits the new five-roll set.
  • Consider the belt type in service. A heavy-duty mining conveyor belt or an abrasion resistant conveyor belt may need different roll spacing and surface options than a lighter fabric core conveyor belt.
  • Review sealing and lubrication needs for dusty environments such as a crushing plant or coal handling system.

For plant operators in sand and gravel lines, cement mills, or port terminals, a five-roll idler set can be a useful upgrade when a standard three-roll set does not give enough belt support. It works alongside the conveyor belt and conveyor pulley, but it does not replace them. Proper selection comes from the conveyor layout, material characteristics, and maintenance plan.